Objective To evaluate the biocompatibility and safety of a novel orthopedics materials-graded zirconia(ZrO2)hydroxyapatite(HA) composite biomaterials. Methods First, ultrafine powers of ZrO2 and HA powder were prepared by chemical precipitation method, then graded ZrO2-HA composite was synthesized by dry-laying and sintering method. After the physiological saline and culture medium extracts of the composite were prepared, four experiments were conducted as follows:① The mouse acute toxic test consists of 2 groups(n=10). The extracts were intravenously injected to mice in the first group, and physiological saline to mice in the second group. The dose was 50 g/kg. Their toxicity manifestation, morality and the change of weight were recorded.② The standard curve of proliferation and metabolism of L929 cells was established. ③ The cytotoxinic test consists of 3 groups: materials group (extracts of the materials), positive control group (culture fluid with 0.64% phenol), and negative control group (RPMI-1640 culture fluid). Each of three was cultured with cell suspension, and then the morphology of the cells was observed, the relative proliferation rate (RGR) was calculated, and the toxicity was classified. ④ In vitrohemolytic test was divided into 3 groups: extracts, sterile distilled water (positive control) and 0.9% physiological saline. In each of three, 0.2 ml anticoagulant diluted fresh rabbit blood was added. The percentage of hemolysis was tested. ⑤ The muscle and implantation test were divided into 4 groups(n=3). The composite biomaterials were implanted into pygal muscleson either side and lateral condyles of femurs. After surgery, the rats of four groups were sacrificed at 12 and 24 weeks respectively.Tissue slice and scanning electronic microscopy were performed. Results General acute toxic test: no mouse died within 3 weeks; no toxicity symptom or adverse effects were shown within 3 days. The weight of materials group increased by 3.57±0.49 g, and the control group by 3.62±0.61 g, showing no statistically significant difference（Ρgt;0.05）.The standard curve of L929 cell perliferation and metabolism showed that their existed a positive correlation between the number of L929 cells and the perliferation. ③ Cytotoxinic test: cytosomes in the positive control group diminished and appeared round, there were pyknotic nucleus, the attached cells agglomerated; the toxicity was level Ⅳ. The morphology of cells in materials groupand negative control group was normal, and the number of them increased; the toxicity was level Ⅰand level 0, respectively. The MTT color experiments showed that positive control group was significantly lower than materials group and negative control group, showing statistically significant difference (Plt;0.01); there was no statistically significant difference between materials group and negative group.④ Hemolytic test: in vitrohemolytic rate of negative control group was0, of positive control group was 100%, and of materials group was 1.66%, which accords with the standard that hemolytic rate should be lower than 5% specified in ISO. ⑤ Implant test:No apparent rejection reaction took place after the composite was implanted; the composite bonded with the bones of the receptors firmly, which had good bonedinduced effect. Conclusion Graded ZrO2-HA composite bioceramic has good biocompatibility and is suitable for orthopedic biomaterials.
Objective To choose the best procedure on preparation of acellularbovine pericardium (ABP) guided bone regeneration (GBR) material. Methods The BP was decellularized with 0.25% Trypsin+0.5% Triton X-100. The acellular bovine pericardiums (ABPs) were treated with phosphatebuffered saline(PBS) (group A), 95% glycerol (group B), EDAC (group C), and EDAC and 95% glycerol (group D) respectively. The treated ABPs were implanted subcutaneously in the back of SD rats respectively at random and no material was implanted as control. Seven rats were sacrificed at 2 weeks, twelve at 4 weeks, twelve at 8 weeks, seven at 16 weeks. Local reaction was studied grossly. The amount of antigen presenting cell (APC) and the percentage of ABP degeneration were reckoned by images analysis system. Results The ABPs were replaced by fibroblasts completely in group A at 8 weeks， in group C at 16 weeks, but only less than 50% till 16 weeks in groups B and D. In all groups, the depth of surrounding fibres attenuated timedependingly. The APC amount of the groups B and D was higher than that of the control group, and the ABP of the groups B and D degraded partly at 16 weeks. Conclusion The ABP treated with EDAC can be replaced by the surrounding tissues and has good biocompatibility.
Objective To review the current researches of scaffold materials for skeletal muscle tissue engineering, to predict the development trend of scaffold materials in skeletal muscle tissue engineering in future. Methods The related l iterature on skeletal muscle tissue engineering, involving categories and properties of scaffold materials, preparative techniqueand biocompatibil ity, was summarized and analyzed. Results Various scaffold materials were used in skeletal muscle tissue engineering, including inorganic biomaterials, biodegradable polymers, natural biomaterial, and biomedical composites. According to different needs of the research, various scaffolds were prepared due to different biomaterials, preparative techniques, and surface modifications. Conclusion The development trend and perspective of skeletal muscle tissue engineering are the use of composite materials, and the preparation of composite scaffolds and surface modification according to the specific functions of scaffolds.
Objective To investigate the biocompatibility of acellular urinary bladder submucosa (AUBS). Methods The acellular collagen matrix of human urinary bladder submucosa was developed using freeze-thawed enzymatic treatment and freeze-drying technique. Human oral keratinocytes were cultured and seeded on AUBS at a density of 2×106/ml in vitro.The proliferation of the cells were observed. Pockets were created in the abdominal muscle wall of 18 SD rats. AUBS in size 1 cm×1 cm was implanted into the pocket. The grafts were observed by light microscope 3, 6, 10, 14, 21 and 28 days after operation. Results AUBSmainly consisted of collagen fibers with a three-dimensional network structure. After the oral keratinocytes were seeded, continous oral epithelium layer was formed on the surface of AUBS after 10 days in vitro. Histological observation of the grafted AUBS showed progressive cell infiltration at 6 days. New capillaries formed at 14 days. The collagen fibers arranged regularly at 28 days after implantation. Conclusion Freeze-dried AUBS may be used as a suitable scaffold for tissue regeneration, which can induce cell proliferation both in vivo and in vitro and has good biocompatibilty.
OBJECTIVE To study the biocompatibility of skin reproductive membrane. METHODS According to ISO’s standards, the extractions of the skin reproductive membrane were prepared, and the acute systematic toxicity test, primary skin irritant test, cytotoxicity test, gene expression of type I collagen and fibronectin were detected to evaluate the biocompatibility of skin reproductive membrane. RESULTS All of those tests showed negative results. CONCLUSION The skin reproductive membrane has excellent biocompatibility in the level of the systematic, cellular and molecular biology.
ObjectiveTo explore the biocompatibility of the poly-lactide-co-glycolide (PLGA)/collagen type I scaffold with rat vaginal epithelial cells, and the feasibility of using PLGA/collagen type I as scaffold to reconstruct vagina by the tissue engineering. MethodsPLGA/collagen type I scaffold was prepared with PLGA covered polylysine and collagen type I. The vaginal epithelial cells of Sprague Dawley rat of 10-12 weeks old were cultured by enzyme digestion method. The vaginal epithelial cells of passage 2 were cultured in the leaching liquor of scaffold for 48 hours to detect its cytotoxicity by MTT. The vaginal epithelial cells were inoculated on the PLGA/collagen type I scaffold (experimental group) and PLGA scaffold (control group) to calculate the cell adhesion rate. Epithelial cells-scaffold complexes were implanted subcutaneously on the rat back. At 2, 4, and 8 weeks after implantation, the epithelial cells-scaffold complexes were harvested to observe the cell growth by HE staining and immunohistochemical analysis. The epithelial cells-scaffold complexes were transplanted to reconstruct vagina in 6 rats with vaginal defect. After 3 and 6 months, the vaginal length was measured and the appearance was observed. The neovagina tissues were harvested for histological evaluation after 6 months. ResultsThe epithelial cells grew and proliferated well in the leaching liquor of PLGA/collagen type I scaffold, and the cytotoxicity was at grade 1. The cell adhesion rate on the PLGA/collagen type I scaffold was 71.8%±9.2%, which significantly higher than that on the PLGA scaffold (63.4%±5.7%) (t=2.195, P=0.005). The epithelial cells could grow and adhere to the PLGA/collagen type I scaffolds. At 2 weeks after implanted subcutaneously, the epithelial cells grew and proliferated in the pores of scaffolds, and the fibroblasts were observed. At 4 weeks, 1-3 layers epithelium formed on the surface of scaffold. At 8 weeks, the epithelial cells increased and arranged regularly, which formed the membrane-like layer on the scaffold. The keratin expression of the epithelium was positive. At 3 months after transplantation in situ, the vaginal mucosa showed pink and lustrous epithelialization, and the majority of scaffold degraded. After 6 months, the neovagina length was 1.2 cm, without obvious stenosis; the vaginal mucosa had similar appearance and epithelial layer to normal vagina, but it had less duplicature; there were nail-like processes in the basal layer, but the number was less than that of normal vagina. The immunohistochemistry staining for keratin was positive. ConclusionThe PLGA/collagen type I scaffolds have good cytocompatibility with the epithelial cells, and can be used as the biodegradable polymer scaffold of the vaginal tissue engineering.
To explore the histological and the hematological change of rabbits after implanting novel injectable artificial nucleus prostheses, and to evaluate the biological safety. Methods In accordance with Biological Evaluation of Medical Devices, materials of polyurethane, sil icone rubber and macromolecular polyethylene for medical use were made into short column 1 cm in length and 0.3 cm in diameter. Forty-eight SPF New Zealand white rabbits weighing 2.5-3.0 kg were used, and cavity 1 cm in depth was made in the area 2 cm away from the spinal midl ine by separating muscle.Then according to different material being implanted, the rabbits were divided into 3 groups (n=16): Group A, polyurethane; group B, sil icone rubber; group C, macromolecular polyethylene for medical use as negative control. General condition of the rabbits was observed after operation. Gross and histology observation were conducted 1, 4, 12 and 26 weeks after operation. Blood routine, biochemical function and electrolyte assays were performed 26 weeks after operation to observe pathological changes of organs. Meanwhile, physicochemical properties of the materials were detected, and the material in the same batch was used as negative control. Results All rabbits survived until the end of experiment, and all wounds healed by first intention. In each group, red swollen muscles were observed 1 week after operation and disappeared 4 weeks after operation, connective tissue around the implanted materials occurred 12 and 26 weeks after operation. At 26 weeks after operation, there were no significant differences among three groups in blood routine, biochemical function and electrolyte assays (P gt; 0.05). Organs had smooth surface without ulceration, ecchymosis, obvious swell ing, hyperemia or bleeding, and nodules. There were no significant differences among three groups in percentage weight of each organ (P gt; 0.05). Histology observation: granulation tissue prol iferation and inflammatory cell infiltration were observed in each group 1 week after operation, fibrous capsule formation around the materials and the disappearance of inflammatory cell infiltration were evident 4 weeks after operation, cyst wall grewover time and achieved stabil ity 12 weeks after operation. The inflammatory response and the fiber cyst cavity of groups A and B met the standard of GB/T 16175 and were in l ine with group C. No specific pathological changes were discovered in the organs 26 weeks after operation. For group A, no significant difference was evident between before and after material implantation in terms of weight average molecular weight, number average molecular weight, tensile strength at break and elongation at break (P gt; 0.05). For group B, no significant difference was evident between before and after material implantation in shore hardness (P gt; 0.05). Conclusion Novel injectable nucleus pulposus prostheses do not damage local tissue and function of organs, but provide good biocompatibil ity and biological safety.
Objective To investigate the effect of human tooth bone graft materials on the proliferation, differentiation, and morphology of macrophages, and to understand the biocompatibility and cytotoxicity of human tooth bone graft materials. Methods Fresh human teeth were collected to prepare human tooth bone graft materials, the adhesion of mouse mononuclear macrophages RAW264.7 to human bone graft materials was observed under confocal microscopy. Scanning electron microscopy was used to observe the morphology of human tooth bone graft materials, OSTEONⅡ synthetic highly resorbable bone grafting materials, and untreated tooth powder (dental particles without preparation reagents). Different components of the extract were prepared in 4 groups: group A (DMEM medium containing 10% fetal bovine serum), group B (human tooth bone graft materials), group C (OSTEONⅡ synthetic highly resorbable bone grafting materials), group D (untreated tooth powder without preparation reagents). The 4 groups of extracts were co-cultured with the cells, and the cytotoxicity was qualitatively determined by observing the cell morphological changes by inverted microscope. The cell proliferation and differentiation results and cell relative proliferation rate were determined by MTT method to quantitatively determine cytotoxicity. The cell viability was detected by trypanosoma blue staining, and tumor necrosis factor α (TNF-α ) and interleukin 6 (IL-6) expressions were detected by ELISA. Results Scanning electron microscopy showed that the surface of the human tooth bone graft material and the OSTEONⅡ synthetic highly resorbable bone grafting materials had a uniform pore structure, while the untreated tooth particle collagen fiber structure and the demineralized dentin layer collapsed without specific structure. Confocal microscopy showed that the cells grew well on human tooth bone graft materials. After co-culture with the extract, the morphology and quantity of cells in groups A, B, and C were normal, and the toxic reaction grades were all grade 0, while group D was grade 3 reaction. MTT test showed that the cytotoxicity of groups B and C was grade 0 or 1 at each time point, indicating that the materials were qualified. The cytotoxicity was grade 2 in group D at 1 day after culture, and was grade 4 at 3, 5, and 7 days. Combined with cell morphology analysis, the materials were unqualified. The trypanosoma blue staining showed that the number of cells in groups A, B, and C was significantly higher than that in group D at each time point (P<0.05), but no significant difference was found among groups A, B, and C (P<0.05). ELISA test showed that the levels of TNF-α and IL-6 in groups A, B, and C were significantly lower than those in group D (P<0.05), but no significant difference was found among groups A, B, and C (P<0.05). Conclusion The human tooth bone graft materials is co-cultured with mice mononuclear macrophages without cytotoxicity. The extract has no significant effect on cell proliferation and differentiation, does not increase the expression of inflammatory factors, has good biocompatibility, and is expected to be used for clinical bone defect repair.
The poor mechanical property and vulnerability to bacterial infections are the main problems in clinic for dental restoration resins. Based on this problem, the purpose of this study is to synthesize silver-titanium dioxide (Ag-TiO2) nanoparticles with good photocatalytic properties, and add them to the composite resin to improve the mechanical properties and photocatalytic antibacterial capability of the resin. The microstructure and chemical composition of Ag-TiO2 nanoparticles and composite resins were characterized. The results indicated that Ag existed in both metallic and silver oxide state in the Ag-TiO2, and Ag-TiO2 nanoparticles were uniformly dispersed in the resins. The results of mechanical experiments suggested that the mechanical properties of the composite resin were significantly improved due to the incorporation of Ag-TiO2 nanoparticles. The antibacterial results indicated that the Ag-TiO2 nanoparticle-filled composite resins exhibited excellent antibacterial activities under 660 nm light irradiation for 10 min due to the photocatalysis, and the Ag-TiO2 nanoparticle-filled composite resins could also exhibit excellent antibacterial activities after contact with bacteria for 24 h without light irradiation because of the release of Ag ions. In summary, this study provides a new antibacterial idea for the field of dental composite resins.
Objective To evaluate the histocompatibil ity of porous hydroxyapatite (HAP) coating NiTi shape memory alloy and to provide a theoretical basis for its cl inical appl ication in bone defect repair. Methods Twenty-four Chinchilla rabbits weighing 2.0-2.5 kg were randomized into experimental group and control group (n=12). HAP coating NiTi shape memory alloy was implanted into the distal part of left femur of 12 rabbits in the experimental group, while holes without alloy implantation were performed on the control group. At 7, 14, 28 and 56 days after implantation, the animals werekilled (3 rabbits in each group at a time). Gross observation, histology observation, BMP-2 immunohistochemistry observation and image grey scale analysis were performed. And the histology observation was evaluated by GB/T16886.6-1997 in terms of inflammation, capsule wall of fibrous tissue, materials degradation and the response of peripheral tissue. Results All of the animals survived until being killed. The implants reached a peak embedded in bone tissue wholly, without loosening and bone absorption. The inflammatory cell infiltration and fibrous hyperplasia were at 7 days after implantation, with the formation of cyst wall of fibrous tissue and the implant wrapped by the cyst wall. The response of connective tissue proliferation was still obvious in partial samples of experimental group at 56 days after implantation, which was wrose than the control group but consistent with the in vivo implantation standard of GB/T16886.6-1997. Immunohistochemistry observation displayed the endogenous BMP-2 were in the cytoplasm of MSCs and osteoblast. The result of image analysis showed the expression of BMP-2 were staged in line with the repair of bone defect, two groups witnessed the peak expression of the BMP-2 at 14 days after implantation. There wereno significant differences among different time points in the staining gray scale of BMP-2 (P gt; 0.05). Conclusion HAP coating NiTi shape memory alloy, as a biomedical material, has excellent histocompatibility with bone.